SMART results from unraid system, one failing drive, Aug 2014

Leave a comment

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (36360) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always – 0
3 Spin_Up_Time 0x0027 161 159 021 Pre-fail Always – 6908
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always – 1445
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always – 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always – 0
9 Power_On_Hours 0x0032 074 074 000 Old_age Always – 19669
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always – 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always – 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always – 159
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always – 15
193 Load_Cycle_Count 0x0032 194 194 000 Old_age Always – 19967
194 Temperature_Celsius 0x0022 117 099 000 Old_age Always – 33
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always – 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always – 15
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline – 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always – 0
200 Multi_Zone_Error_Rate 0x0008 200 199 000 Old_age Offline – 0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@Tower:/var/log# smartctl -a -A /dev/sde
smartctl version 5.38 [i486-slackware-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: WDC WD2001FASS-00U0B0
Serial Number: WD-WMAUR0148740
Firmware Version: 01.00101
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Tue Aug 12 19:27:04 2014 Local time zone must be set–see zic m
SMART support is: Available – device has SMART capability.
SMART support is: Enabled

Device Model: WDC WD2001FASS-00U0B0
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (31500) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 193 193 051 Pre-fail Always – 356070
3 Spin_Up_Time 0x0027 040 040 021 Pre-fail Always – 15000
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always – 1601
5 Reallocated_Sector_Ct 0x0033 129 129 140 Pre-fail Always FAILING_NOW 567
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always – 0
9 Power_On_Hours 0x0032 071 071 000 Old_age Always – 21609
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always – 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always – 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always – 299
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always – 18
193 Load_Cycle_Count 0x0032 196 196 000 Old_age Always – 13644
194 Temperature_Celsius 0x0022 115 105 000 Old_age Always – 37
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always – 507
197 Current_Pending_Sector 0x0032 198 197 000 Old_age Always – 698
198 Offline_Uncorrectable 0x0030 198 198 000 Old_age Offline – 943
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always – 0
200 Multi_Zone_Error_Rate 0x0008 001 001 000 Old_age Offline – 1453784

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

root@Tower:/var/log# Device Model: WDC WD2001FASS-00U0B0
-bash: Device: command not found
root@Tower:/var/log# smartctl -a -A /dev/sdf
smartctl version 5.38 [i486-slackware-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

Device: Kingston DT 101 II Version: 1.00
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
>> Terminate command early due to bad response to IEC mode page
A mandatory SMART command failed: exiting. To continue, add one or more ‘-T permissive’ options.
root@Tower:/var/log#

No related posts.

Misc Links , ,

Leave a Reply

Your email address will not be published. Required fields are marked *